![]() If you'd like to simulate the project yourself, check out the simulation files in the repository folder entitled "Simulations".Ĭontact Information: I hope this information helps you learn more about combinational logic design. ![]() Status of My Project: My project works perfectly using only 6 logic IC's from the 74HC74 logic series. Thunderbird Year 1966 7 The first image is the motor on the right with the cover off. Design simulation was completed in logisim, a free educational tool for designing and simulating digital logic circuits. For more information on the theory and circuit design, please see the wiki.Ĭredits: As mentioned previously, I completed this project with fellow ENGR 357 student, Konrad McClure. I worked with Konrad McClure to build the combinational logic circuit. This project was created in partial fulfillments of ENGR 354 "Digital Logic" at Walla Walla University. Lamps are good, wireing in trunk feeding the. The sequintial flasher, the turn signal relay and the stop lamp relay in trunk have all been replaced to no avail, problem not corrected. 1966 1967 1968 FORD THUNDERBIRD SEQUENTIAL REAR TAILLIGHT RELAY C7SZ-13482-B NOS (1) 119.00 13.36 shipping 16 watching 1968 FORD THUNDERBIRD TBIRD Rear Side Marker Light Lamp LH 40.00 16.10 shipping Benefits charity New 1965 Ford Thunderbird 1968 - 1970 Shelby Mustang New Tail light lens brake 95.00 38. Introduction: This repository covers the design of simulates the sequential tail light operation of the 1966 Ford Thunderbird using 74HC74 logic. Left & right outer lamps do not flash when turn signals are activated (sequentially) all lights do operate when brakes are applied. I'm not sure how robust the Dodge turn signals switches are but this is a failure point in the Fords with 6 tail lights.1966 Ford Thunderbird Tail Lights Control Note: It is highly recommended to convert the rear lamps to LEDs because of the high current that is drawn by incandescent 1157 bulbs. Orange/blue, orange/white, and orange/red are RH. The rear tail light connections are shown in the schematic: green/orange, green/red, green/black are LH, Note: They must not connect to the turn signal switch directly.ħ. The white/blue and green/white wires from the 6-pin relay connector feed the R & L front turn signal lights. The R & L front light wires from your turn signal switch connect to the 8-pin relay connector, violet and white.Ħ. Both R & L rear signal feeds from your turn signal switch connect to the orange/green wire on the motor-driven sequencer.ĥ. The stop lamp relay output, 14 ga green, feeds the 14 ga green/white wire on the 6-pin relay connector.Ĥ. The stop lamp relay 14 ga red wire needs +12V. The output of the stop lamp switch feeds the 18 ga green/white on the stop lamp relay.Ģ. If you review the schematic, you will find:ġ. ![]() It is solely used to drive the motor around to the start position after the turn signal lever is returned to the neutral position. The unit is in the trunk by the back seat. The T- Bird sequencer has an additional 2-pin connector with brown, brown/white wires. the 65 has the sequential taillights and if you have the original module it may be shorted out. You have the late '66 T-Bird system with the 4-pin flat stop lamp relay. C35) 1968 Thunderbird Sequential Turn signal Harness REPAIR kit (Fits: Ford Thunderbird) 34.95. T21-6) 1965 1966 Thunderbird Turn Signal Indicator Relay C5SZ-13A366-CR (Fits: Ford Thunderbird) 125.95. I just have a mess right now on the table of un taped wiring and miss matched plug ends. Tail Light Assemblies Accessory Lighting. So, what will do is run forwards with the wiring to the turn signal switch and stop light switch. It's in the tail end of my 1967 Dodge Coronet 500. Plug-n-play Operation, Direct Bolt-on OE Fitment or Replacement for the Stock. Okay, now, here's the kicker, don't be unit isn't in a 1966 T Bird. Monzter Automotives Mustang sequential tail light kit fits the 2005-2009. I have the schematics and have figured out the numbers on the wires and the color codes. What plugs into what? What plugs into the three units bolted to the rubber plate. What I need is a definitive photo of what the entire tail light harness is supposed to look like. One end has been cut through and I think i'm missing some connectors with pins. It's in three pieces and mostly untaped from the factory wrappings. I have a 1966 T Bird tail light system with the rubber patch holding the sequencer, relay and switch, and the old harness that is in poor shape.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |